Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: RR and 1/4mile today

  1. #1
    Fee
    Guest

    RR and 1/4mile today

    The punto did well.....

    162bhp (125 at the wheels) and 190lb/ft at 3780rpm

    sounded quite healthy, no smoke at all..... and 101k miles..... bring it on



    The skyline was a bit pants on the rollers.... It really held back around 4000 and picked up again at 5500rpm...... I'll get an excel graph knocked up as i threw my scanner out LOL

    Its had new 0.8mm iridiums ..... must be a duff coil pack or two

    It made 200bhp RWHP.... 213lb/ft at 4020rpm






    1/4mile times...... (very slippy)

    Skyline:

    14.736 at 94.5mph
    14.738 at 99.6mph
    14.781 at 97.0mph

    best and worst 60ft = 2.382 and 3.036
    best and worst TV = 99.6mph and 88.2mph (rolled over hehe)

    Punto:

    15.260 at 93.0mph
    15.279 at 91.3mph
    15.290 at 93.2mph

    Best and worst 60ft = 2.432 and 2.857
    Best and worst TV = 99.6mph and 49.8mph (1st to 4th.... hehhe)

  2. #2
    nakajima
    Guest
    take it its not a GTR then ?

    good to see the gT is running healthy again fee.

  3. #3
    Fee
    Guest
    no, its a GTSt (says that on the graph numbnuts )

    its 200bhp at the wheels.... just under flywheel book (250) figure at 240. Adam thinks its either the coil packs or the timing.

    Bit disapointed with the 1/4mile time as it will be the last time it will be raced by me. 15.2 on a wet greasy track isnt too bad i suppose


  4. #4
    nakajima
    Guest
    ooops, just seen the graph. should pay more attention

  5. #5
    Punto Lover
    Join Date
    Jul 2004
    Location
    London
    Posts
    589
    fee what mods do u av on the punto again, thats a good torque figure.....

    komi

  6. #6
    Fee
    Guest
    Allard FMIC (the bigger one)
    S/S (undersized) main boostpipe
    BCPR7's
    Induction kit (could do with being mounted further towards the front of the car)
    MBC Dawes type bleed
    SEB0 ecu
    Dr Evil De-cat
    Scorpion catback exhaust

  7. #7
    Punto know it all
    Join Date
    Nov 2003
    Location
    Milton Keynes
    Posts
    5,653
    190 lb/ft torque and only 125 bhp @ wheels? ??:

    Mine made 121 @ wheels (G-Force Aylesbury) (they don't give you a fly figure as that is only a guess unless you remove the engine and actually measure it), and that was standard.

    James

  8. #8
    Seaniboy
    Guest
    What boost was u runnning?

  9. #9
    Fee
    Guest
    they never mapped the pressure.... but it was holding around 16psi till redline on the 1/4mile

  10. #10
    Dan_R
    Guest
    what rollers was that fee?

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •