i wasnt planning on a new project so soon
pm me a price for just the shell then a price with all the bits on there might be a 2.0 16vt for sale soon lol
o.k. People just trying to see if there is any interest in my shell, which I started prepin from my project track car.
For those who don't know about what I started and what work has been done, you should look at my old project thread which contains photos and a little walk throu what I have done:
http://www.puntosports.co.uk/forums/...ight=red+devil
- Car is total stripped in side
- All the sound deadening crap has been removed
- Floor plans were cleaned up (inside & out) could do with a bit of a sproose up
- What little rust the shell had was treated (only bit was near the filler neck brackets see project thread)
- A fresh coat of under seal applied to the underneath to protect it
- The front windscreen will need replacing as it has been cracked
- The left hand side rear has a minor dent as per this pic:
http://i248.photobucket.com/albums/g...l/DSCF0287.jpg- The front suspenstion leg mounting points have been strenghtend with a thick wedge of steel. Although they could do with being cleaned up a bit now as they have rusted a little bit.
- The rear housing/arches inside have had a thick plate of steel wealded for mounting rear legs of a roll cage, as per MSA blue book spec.
- Other points in the shell have been prepared ready for cage mounting points.
The shell is a good base for anyone wanting to build a good track car or anything to be used for all things fun.
Cosmetically it doesnt look too hot,the body work is not perfect as it has a few dings and paint is faided, that never bothered me as it was going to be finished with a fresh paint job inside out but the shell is very good with vertually no rust.
The main things is that the shell is very very good base condition for such a project to be built from, I also belive it spend a good time out in malta which is a nice hot & dry place which is why isnt rotten like some found over here.
Currently I am just looking to see if any one is interested in the shell only as a lot of work has gone into prepin it and I think it would be a shame to scrap it and lose out on all the time, money and effort that I put into it so far.
So the bare shell with REG & V5 Log book is on offer.
If I can't sell the shell then everything will go into storage for me to come back to in later years. If I sell the shell then many other goodies for building a big spec Punto will be up for grabs including the roll cage with extra bars ect
If anyone is interested in a bit of a package deal such as a rolling shell with F&R refurbed subframes ect or with the roll cage then talk to me.
Please PM me or email andyc@xlerate.net if interested
price wise... I really do not know but I am open to offers to see what people are thinking they would pay for it.
i wasnt planning on a new project so soon
pm me a price for just the shell then a price with all the bits on there might be a 2.0 16vt for sale soon lol
GLWTS, out of curiosity what are you doing with all the parts bought?
If I sell the shell, I will then sell everything else.
i.e. everything that I have collected for the build
Roll Cage with extra bars, TT Stage 2 Turbo, New Piper Fast Road Cam, Forged Rods, Wosner Forged Pistons, POTR BVH, New Quaife LSD, New Eibach Anti Roll Bars Kit, Spax Coilovers, New wishbones with poly bushes, Baileys Header Tank, Pace Intercooler with Twin DV outlets, 2x Bailey DV's New Alloy Rad, SFS Red Silcone hoses all over the place, New Dr Evil 2.5" Turbo Elbow, New Dr Evil 2.5" Downpipe, New Tubular Exhaust Manifold, Parts to make a new exhaust system inc back box..... the list goes on and on lol
If I don't sell the shell then I'll put it all in my spare empty garage and come back to it maybe next year.
Also guys if I do get a resonable price for the shell, just so that you have an idea about the cage side of things, Demon Tweeks have it listed for about the £580 mark:
http://www.demon-tweeks.co.uk/Applic...d=27628-1893-C
So I would be looking for atleast this for the cage, this would also include the two extra bars that are made ready to be wealding in. One is for the bottom of the legs of main hoop and the other bar is for the going accross the rear legs which act as a kind of rear strut and also somewhere to affix the harnesses to.
Thanks
You just remember who gets first dibs on all the goodies!
o.k. guys will try and give people an idea of what I'm thinking
I think that it would be best & easyest to sell as a rolling shell that can be rolled onto a trailer, this can have extra goodies left on such as coilovers, ARB's and cage if the buyer also wanted to buy such items as well or I can go to a local breakers put on old standard stuff on to keep it a rolling shell or simply leave/take off.
If you look at my project thread you can see the bits below/work that has been done
The rolling shell would have fitted/come with also:
- Front refurbished subframe with all new bolts
- New front wishbones which cost £29.89 each from shop4parts fitted with powerflex poly bushes which cost £20 & new nuts & bolts fitted
- Refurbished front hub carriers (shot blasted, primered and re painted in matt black)
- New set of front hubs which cost £41.99 each from shop4parts
- New set of bearings which cost £39.29 each from shop4parts (although I think the garage that pressed in the bearings looked have damage the one on the passenger side so that one might need replacing, not sure)
- New set of track rod ends fitted which cost £14.80 each from shop4parts
- A nice clean power steering rack from a GT with standard GT stearing wheel & colume fitted
- Refurbished rear subframe with all new bushes (which cost £32 for the full set from shop4parts) pressed in & new bump stops fitted
- Rear swing arms attached with new nuts/bolts, hubs have done about 5k miles
- Some old standard front suspension legs would be fitted
- Some old rear suspension dampers & springs would be fitted
- Some old random fiat fitment wheels
- Some old f&r bumpers chucked in if buyer wanter to go down the sleeper look
- A GT Dash board (but no clocks or wire loom)
All the above & the new parts cost a small fortune to buy and refurbish
PRICE: £550
(bare shell i.e. non rolling shell with most of the above removed, I would be looking for around £250 mark but I can see it being a bit tricky to take away/transport with non of the above on it.
Other items from my big spec build project which I have if people are interested in?
(Please note that I can take pics and provide prices upon request) or I might list each items seperately / stick them all on ebay... don't know yet it depends if the shell sells or if I keep the lot.
Sparco 6point Roll Cage with extra bars
Spax RSX Adjustable Coilovers
New Eibach Anti Roll Bar Kit
GT3 Alloy Front Strut Brass
New Quaife LSD QDH2K
Brand New Helix Organic Clutch Kit - inc Plate/Cover/Bearing
GT3 Gearbox approx 100k miles taken off working car
Short Shifter with OMP Gear Knob
POTR BVH
Standard GT3 head with small hairline cracks approx 100k miles
GT3 Lightend & Balanced Fly Wheel
Lightend & Balanced crank with all new shells set
New Piper FIAUNOTBP270-B GT Fast Road Cam
New 16 Row Oil Cooler with new custom Braided Lines & Sandwich Plate
New Alloy Rad
Pace Front Mount Intercooler with custom twin Dump Valve outlets
81.5mm Wossner Forged Pistons & Forged Rods
GT3 Block with 81.5mm bores
TT Stage 2 Turbo miles unknown estimate approx 10k-15k miles can work out if need be
New 4 Branch Tubular Manifold
New 2.5" Dr Evil Turbo Elbow
New 2.5" Dr Evil Downpipe
Parts to make a Custom 2.5" Exhaust system inc bends, straight pipe, back box and 3" tailpipe with Power Flex Exhaust mounting bushes
New motorsport braided fuel lines (enough to replace all standard lines)
FSE Power Boost Valve with braided line into Ractech in car Gauge
New Full Orignal GT3 Gasket Set from Fiat
New M10 Head Stud Set from Fiat
GT3 All New Belts Set from Fiat
GT3 New Rocker Cover from Fiat
New GT3 Water Pump
New GT3 Thermostat
GT3 Oil Pump taken from working car approx 100k miles
GT3 AFM taken from working car approx 100k miles
GT3 Inlet Manifold shot blasted and repainted in silver/metal look
2x Bailey DV26 black Dump Valves
GT3 ECU with SEB4.1 Chip
New set of 330cc injectors
Used set of Bosch 304cc Injectors
Alloy PAS tank
Baileys Alloy Header tank
Boloume Chrome Top Boost Pipe
3" Alloy AFM Pipe with required SFS red silcon hoses
PiperX Air Filter from Ford Sierra Cosworth
50mm Stainless Steal Turbo to FMIC boost pipe inc SFS red silcon hose
Racetech Air Fuel Ratio Meter gaget
New Carbon Fibre Door Cards Set
New ABS Motorsport Fibreglass Door Cards Set
OMP Race Steering Wheel
GT3 Seats
Luke 4 point harnesses
Head up display dial/dash kit
Brembo 4 Pot Calipers set up inc Brackets, Used 330mm Disks & Pads and new caliper refurb kits
used but good Rear EBC Disks & green stuff pads for GT3
used but good Front EBC Disks & green stuff pads for GT3
Fiat 10mm Wheel spacers (set of two)
Set of 4x 17" Team Dynamic Pro Race Black Multi Spoke wheels wrapped in part worn rubber
Black Morret Head Lights
Black Bad Boy Bonnet with Cool Louvers
Black smoothed rear tailgate with small crack in paint job
New rev limit rear bumper
Refurbished GT3 rear break calipers as per project thread painted in RD HT Paint
Black Beast Front bumpers in need of refurb
What are you doing with all this stuff now Andy?
Hi Guys
No sale on the shell... so all going to be stored to come back to in future