Page 30 of 30 FirstFirst ... 20252627282930
Results 291 to 299 of 299

Thread: Building a MS1 ecu for a Punto GT

  1. #291
    PSC Trader DR_EVIL's Avatar
    Join Date
    Jul 2003
    Location
    Middlesbrough
    Posts
    3,385
    Quote Originally Posted by kubito View Post
    I think my settings isnt good because car doesnt running well.
    I have MAP 250kPa
    lambda Innovate LC-1 on idle-16AFR
    temps in C
    sensors are calibratet I hope well
    Idling too lean, Add fuel.

    I Idle at 12-13:1 afr

  2. #292
    Punto Enthusiast
    Join Date
    Feb 2011
    Location
    Czech Republic
    Posts
    81
    I use your external wiring Pete. Its Pin 47GT to Pin 2MS crank sensor ground and Pin 48GT to pin 24MS its signal wire. thats right? I have jumper from TSEL to VROUT

    rotational speed I still fall to zero even if the car is running. I tried to adjust the resistors R52 and 56 but no change.
    I tried various maps of the fuel and ignition. but once I open up the throttle and the car is not up to speed at all.

    ok I add fuel on idle. but this does not solve my problem.

    I dont have a MAPDADDY but only a MAPX4250AP.
    but my tooth logger looks like this:

    http://imageshack.us/photo/my-images...oothloger.png/

  3. #293
    PSC Trader DR_EVIL's Avatar
    Join Date
    Jul 2003
    Location
    Middlesbrough
    Posts
    3,385
    Your vr is wired backwards, swap the + and -

  4. #294
    Punto know it all
    Join Date
    Jul 2009
    Location
    leeds
    Posts
    2,552
    Odd question but does mega squirt log knocking through the knock sensor or do you have to do that yourself?

  5. #295
    Punto Enthusiast
    Join Date
    Feb 2011
    Location
    Czech Republic
    Posts
    81
    I dont use knock.

  6. #296
    Punto Enthusiast
    Join Date
    Feb 2011
    Location
    Czech Republic
    Posts
    81
    ok I must swap pins 24 and 2 . I will go try it. Thanks

    ok Punto runs very well :-) many thanks for help guys

    last question: I have msq file from Hobizoli and I chcek his settings for rev counter. I will set up same but my rev counter doesnt work still.
    Last edited by kubito; 15th March 2012 at 20:18.

  7. #297
    PSC Porn king
    Join Date
    Jun 2006
    Location
    Budapest, Hungary
    Posts
    2,937
    Quote Originally Posted by kubito View Post
    I think my settings isnt good because car doesnt running well.
    I have MAP 250kPa
    lambda Innovate LC-1 on idle-16AFR
    temps in C
    sensors are calibratet I hope well
    i have 400kPa MAP

  8. #298
    Punto Enthusiast
    Join Date
    Feb 2011
    Location
    Czech Republic
    Posts
    81
    everything works well.
    Last edited by kubito; 18th March 2012 at 18:54.

  9. #299
    Punto Enthusiast
    Join Date
    Feb 2011
    Location
    Czech Republic
    Posts
    81
    When i use a launch control. I must install a low or high input or both? I have a clutch switch.

    Any one use it?

    Thanks Kubito
    Last edited by kubito; 27th March 2012 at 14:38.

Page 30 of 30 FirstFirst ... 20252627282930

Similar Threads

  1. Building the MS Stimulator
    By DR_EVIL in forum Dr Evil Stainless Exhausts & Tuning
    Replies: 0
    Last Post: 6th October 2011, 14:26
  2. Engine building
    By addzzp in forum Punto Chat
    Replies: 13
    Last Post: 20th November 2009, 20:51
  3. Building a sub box...
    By OMGWTF in forum I.C.E., Security and Electrical
    Replies: 12
    Last Post: 6th March 2008, 00:10
  4. And so it begins... BBQ Building
    By Puntoboy in forum Punto Images
    Replies: 65
    Last Post: 5th August 2007, 11:24
  5. building PC
    By shamster in forum Technobabble
    Replies: 30
    Last Post: 25th February 2005, 12:23

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •