Search:

When i use a launch control. I must install a low or high input or both? I have a clutch switch.

Any one use it?

Thanks Kubito

everything works well.

ok I must swap pins 24 and 2 . I will go try it. Thanks

ok Punto runs very well :-) many thanks for help guys

last question: I have msq file from Hobizoli and I chcek his settings for rev...

I dont use knock.

I use your external wiring Pete. Its Pin 47GT to Pin 2MS crank sensor ground and Pin 48GT to pin 24MS its signal wire. thats right? I have jumper from TSEL to VROUT

rotational speed I still fall...

I think my settings isnt good because car doesnt running well.
I have MAP 250kPa
lambda Innovate LC-1 on idle-16AFR
temps in C
sensors are calibratet I hope well

Hi Acki,
my injectors is high Z 440ccm my req fuel is 5.2ms

My log looks like this. what I must wired??

When I connect my MS in the car and at idle the car runs beautiful. but when you open the throttle and the car is not at all not going to speed.

can someone please send settings for outputs and...

my megasquirt must have: a jumper from VRIN to TACHSELECT, jumper from TSEL to VROUT , also I used TIP120 for PWM. and need two BIP for igniting the two coils. I also have a jumper from JS10 to...

Please advise me someone. I need to diagram the Bosch Motronic M2.7 I have a diagram but the wires are in the car otherwise

Thanks

Hi,

I need advice on how to engage external wires to the ECU. I have a problem where mounted ignition? how to involve phase sensor to megasquirt? and where to engage coil pack? the VR sensor has...

Hi everyone, I ECU into the car I want to connect the connector to the original ECU. But do not know how I do it confuses anyone involved in scheme? where the wire should I participate? Thank you

yes I looked too. I still like a man, and will challenge even before the U5. and when I remove F1 I have a 4.8V on right leg U5.

yes I looked too. I still like a man, and will challenge even before the U5.

So I got the U4 memory on Daughter Card. I tried to replace the regulator U5 without success but I still everywhere only 4V. everything, I still check once but without success.

step 65: high-current ignition driver circuit.

it says that there can be either 330ohm (for 5V) or 1K (for 12V). I have 12V so there should I have 1K? I do not understand this step as it should...

so maybe someone will help me see.

still need to know:
You can do this by:
Soldering a 1K ohm resistor to the hole S12 Marked Immediately below R57 (this gives a 12 Volt pullup), or solder...

So I contacted them and I was told that it not be granted at all because I am from another country. but he sent me a link to someone who would be able to help me.

I look at it thanks. I wanted it from UK because it would be cheaper for me. or a messenger to UK on the right the whole unit if I do not know what to do.

so I guess I'll have to buy a new Daughter Card. But I need to find out why it happened? everything remained the same connection as before. is somewhere in UK Daughter buy itself?

yes anything else about me gone. I have consulted a home :-(

Here is a picture where it is illustrated. when I joined it to the source so it began playing a little out of the smoke appeared so I immediately disconnected. can not read the inscription on it. so...

So today, I noticed the play of the U4 to Daughter Card and then smoke appeared from him. :-( So the unit is dead. :-(

U5 is the voltage regulator. on his left middle 12V brains I have nothing. I have the right 4V not a bad one controller? does not have 5V on it flat? because everywhere I have it thanks to 4V. You...